1. The laser tube can’t cut through,because of the normal attenuation of the laser tube energy; The position of the laser tube shall be adjusted

2. There are problems with the installation of the laser tube. In the process of installation, the air treatment should be isolated. Otherwise, the air humidity will also produce a fire phenomenon

3. The first installation or subsequent start will appear, and the small amplitude of rotating laser tube can eliminate the bubbles

1: The focus lens has scratches on it

2: The focus lenses are covered with stolen goods.

3: There are cracks in the lens.

4: Focus lens to rot.

5: The specs that focus lens use are not correct.

6: Focusing on the lens pack reaction.

7: Focusing lenses and cutting materials are not the best focal points

8: Focusing lens defilm.

9: The focusing lens is not tightened, causing the cutting to wobble.

10: When the lens is installed, it is not properly installed.

1: Over temperature

2: Too little water

3: Water pipe pressure

4: Excessive dust

5: Excessive scale

6: The alarm is broken and always called the police

7: The refrigeration liquid in the compressor is used up, resulting in excessive temperature and alarm.

8: Conduit with condensed water, resulting in a temperature difference is too big, the water tank is set to the intelligent pattern, temperature difference value is set 2 ℃.

9: The fan doesn't turn. It could be the fan.

10: The water flow is very small, or the water pressure is very small, the water is quite a lot of cases, may be the water pump in the inside is broken or blocked.

1. Adjust the light path

2. If the light path is not adjusted, see if the architecture part is level

1. The smoke pipe is too much clutter to clean up.

2: The fan blades are too dusty and clean.

3: The fan is very old and the speed is too slow.

4: The pipe is broken and has a leak.

5: When the fan turns, it has an unusually sharp sound, which may be the sound caused by the friction of the fan blade.

6: The fan is plugged in and then not turned.

1: After the air pump has a long time and normal aging, the blow will become smaller.

2: The air inlet is clogged with dust and cleaned up.

3: There is oil in the air, and the air is too wet. If the air compressor is used, it should be released frequently.

1. Acrylic: depending on the thickness and the laser power, the general power is higher, the speed is slower and the air is small. Compared with cutting effect, the cutting precision is higher.

2. Teflon: same as cutting acrylic, but blow up a little bit.

3. White cloth: in order to ensure that the cutting is not yellow and not coke, the speed is slow, the power is small, and the air blowing is appropriate.

4. Dermis: the incision must be black

5. Board: the incisions will be blackened or yellowed, and the thin board with appropriate cutting parameters will mitigate these conditions

6. Laser dots: cutting machine can do some work on acrylic, but the effect is far less than that of specialized laser

7. Leather dots: you can make a good effect on leather, and recommend RUIDA control board card.

1, Blow up too small, power is too big, focal length is not right, the focus mirror and mirror have dust, and the light road is slightly partial can cause yellowing.
2. The cutting is not smooth when cutting thin fabrics;
It may be blowing up slightly, blowing the fabric into the honeycomb plate, causing the incision to be smooth.
3: Slow cutting and clicking noise;
Image node is overmuch or hit a line will lead to this situation, because no one node will pause, very dense nodes can cause this kind of noise, or in a place of repeat cutting time, can be identified is too much overlap line, to deal with the graphics.
4: Cut the figure cut to half the time the tentative/stop not moving;
Some other graphics software to produce graphics can not be fully compatible with, will appear this kind of circumstance, can open the graphics with CorelDRAW X4 after copying the graphic, and then create a new page and paste in the past, and then save again. DXF format file, if a single graphics too complex graphics is too big, sometimes loss of data transmission, can also lead to this situation, or by other interference of transmission, retransmission image.
5: After cutting the material of the deep color or the material with heavy smoke, it is changed to a lighter color to cause the yellow surface to become dirty;
This is because when cutting on a graphic on the floor above the smoke glance to light color material, such as to avoid this situation, can use first high-power above the floor of an empty cut several times, using the high temperature of the laser and the soot blowing residue, after cutting the material to go with normal power, won't produce incision bottom yellow dirt.
6: The cutting time causes some areas to be cut off;
Most of this kind of circumstance is caused light path is not straight, to check that the light path can be adjusted, or the floor the area and other places not in the same horizontal plane, lead to cut into that position when not in the best focal length, so the area not to wear, readjust the backplane.
7: Occasionally having a jagged edge at the cutting edge;
This can happen when cutting speed is too fast.
8: Cutting surface has slope when cutting thick material;
Most of this is caused by a slight deflection of the vertical light, which is mainly reflected in the thicker materials, which can be improved after the vertical light is dropped.
9: How to determine whether the material is cut during cutting;
Most of the material will produce smoke when cutting, when cutting smoke is all up, that means the material is not cut, the acrylic material is more obvious.
10: The smoke is particularly large at the time of cutting;
It may be that there are too many holes in the honeycomb board, or that the smoke hole in the top of the machine is blocked up and cleared away.
11: After cutting a big graphics, the sealing is not on;
This is a lot of the X/Y axis actually cutting the size of the X/Y axis at a time when it's not very fast, or maybe. The diagonal of the X axis is biased. If the difference is not large, you can also set the sealing overlap distance at the time of the software guide.
12: There are intermittent breakpoints at the time of cutting. This may be the reason for the water protection switch, the water pressure is not large enough, or the problem of the laser power supply.