There effect: optical fiber: speed of 60-80, from about 3 mm focal, power 20-30, 30, frequency padding and semiconductor the same or slightly thick thin stainless steel plate if single pass black, material will be out of shape, suggest many times to do it. Thicker materials can be used at once.

Rough black: semiconductor and optical fiber are similar, high speed high energy high frequency, specific parameters refer to specific requirements.

White effect: semiconductor and optical fiber, all adopt high - speed and low energy method, the frequency is appropriate low, if be laser clean, suggest appropriate to leave coke.

Color effect: non-gradient color, scattering a graphic to multiple layers, and then classifying different layers for parameter equipment.

Gradient color effect: there is no good plan in the industry. It is usually used to put the material in a low level. But the effect is not manageable.

Depth: only the optical fiber equipment can be used. If there is any requirement for speed, it is recommended to use 30 or 50W optical fiber marking machine. In general, high speed and low frequency are used to clean more than one time.

Dozen black: generally speaking, aluminum can't make the black effect, mostly to play rough black, this kind of situation USES high power, high frequency method to make dozen, fill a time can.

White: the speed can be properly set, the power and frequency are properly lowered

Open mode: this requirement is high, with SPI fiber machine, generally speaking, high power and high speed high frequency method to solve, and the use of multiple cross fill, filling density is less than 0.05. The problem that often encounters is burning side, suggest reducing spot in software.

Strip color: the optical fiber marking machine is cross-filled twice, the speed is 500, the power is 30, the frequency is about 20. If you have problems with burning edges, it is recommended to reduce the light spot. If not, suggest reducing speed or replacing the mirror.

A high frequency optical fiber laser can be selected for SPI and JPT 3. Specific parameters are still to be developed.

it is suggested that the semiconductor marking machine should be used, and the effect will be bright after stripping.

Take photos: the black alumina hits the best picture, turn the picture upside down, use dot mode. Adjust the resolution, speed and power depending on the material.

The effect is varied: plastic material is the most complex. In general, the black nylon plastic in the electrician industry can be used to mark with a fiber or a semiconductor machine.

But the materials and colors used in the 3C industry are all over the world, with the use of optical fiber, terminal pump and uv equipment, and the ultraviolet marking machine is the top of the industry.

Type number: the optical fiber can meet the requirements, but the color of beige is not obvious, it is brown or black. The parameters and plastic materials are generally high in low energy and high energy.

This requirement is mostly used in electronics or optoelectronics.

General use of optical fiber or end pump equipment, speed 500, frequency of about 20, low energy, depending on the paint layer thickness.

In general, the effect of optical fiber stripping is biased towards a clean light blue, and the removal of the end pump is biased towards the heavy cream.

Relief: with CO2 marking machine, high speed and low energy, the filling density recommendation 0.1 can be filled with single filling.

See more in the clothing industry, with co2 marking machine, marking parameters as regular parameters, must adjust the focal length accurately. Otherwise there's a linear texture that doesn't work.

Atomization effect: with co2 laser marking machine, speed and power are not very important, filling should be sparse, laser frequency should be low.

The inner carving crystal USES green light marking machine, conventional parameter engraving, document drawing is very important, in carving technology, the voltage requirement is higher.

Green light marking machine glass wall engraving, the process is not common, and the induction control requirements are stricter.

In the electronics industry, with uv laser marking machine, conventional parameters can be completed.

Can use uv laser marking machine can also use co2 marking machine, ultraviolet effect is better. If the co2 marking machine is used, the scene must be small and the focal length control should be accurate. Speed: 300, frequency 5, power 10 or so.

If the rotation is added, the parameters need to be adjusted, and the rotation factor of the motor must be considered.

This process is used in the kitchen and bathroom industry. The marking parameters are universal parameters. But to remove the glass paint face to face. If there is a black line in the removal of the effect, a secondary cross filling is recommended.

Coating marking: coated with special paint on the circuit board for marking. The process can communicate with the manufacturer, the difficulty lies in the architecture of the production line.

Clean the residue or rust of the metal material, use the optical fiber marking machine, use high speed low-energy low frequency to clean.

The photoelectric industry also has clean optical material say, specific craft is unknown.

Used in the electrician industry, such as the handle of the tool and so on, the optical fiber marking machine can also, but the effect is far less than the ultraviolet, the specific parameters need to be developed.

ECZ software has this feature, which can set variable text and fixed text. Specific actions can be added or deleted depending on the prompts. There is no border change in the skip process. That's because when you fill it, you check it out. By removing this option, the random change of the filling jump number can be realized.